INTAKS® Scaffold & Edge Protection Solutions

Attached Scaffolding – Split Platform

INTAKS® Scaffold & Edge Protection Solutions

Attached Scaffolding – Split Platform

Split Platform is a unique scaffolding and edge protection solution that attaches quickly to the house frame and creates valuable access and working space. This speeds up construction and job scheduling, avoids delays and locks in progress payments.

Benefits

INTAKS Split Platform was specifically designed to allow multiple trades to work on the house at the same time:

  • From top platform, builder can easily step on top plate to install trusses.
  • Planks are then dropped, leaving upper handrails as edge protection for the roofer.
  • Fascia installer is in an upright position to work, not crouched over.
  • Builder is also in a good position to install soffits.
  • While roof is going on, windows can be installed.
  • When scaffold comes down, roof, windows and soffit are all done.
  • Install and dismantle process is fast.
  • Less scaffolding gear on site.
  • Uses building frame to help support the scaffold.
  • Strong but light and easy to load, unload and carry.
Installation process

Install follows a simple, sequential process:

  1. Lay out Soleboards and Screwjacks where Standards are required.
  2. Attach Stud Brackets to building frame.
  3. Configure support frames.
  4. Put support frames into position.
  5. Install top platform with Interlocking Planks.
  6. Create Ladder access and install Swing Gate.
  7. Install Handrails using tool-less Spring Clip mechanism.
  8. Install Toeboards using tool-less Toeboard Plank Clips.
  9. Complete final checks and handover to site manager.
  10. Once trusses are installed, planks are dropped to lower platform.
  11. Dismantle process is the reverse to installation.
Components

Components are strong but light to carry with precision engineering ensuring simple assembly.

For handrails:

  • Handrail Tube (part #HR4 to HR#6)
  • Handrail Joiners/External Sleeve Couplers (part #1165/#SES)
  • Fixed 90° Couplers (part #SFC) and/or Swivel Couplers (part #SSC) – for joining handrails at corners
  • Handrail Post (part #1101) – for safely installing handrails on upper levels

For each support frame:

  • 1 x Soleboard (part #ISB)
  • 1 x Screwjack (part #SSJ450 or #SSJ620)
  • 2 x Extenders (part #1144/#1160)
  • 1 x Standard Arm (part #1172 to #1177)
  • 1 x Standard (part #1178 to #1181)
  • 1 x Wall Bracket (part #1141)
  • 1 x Platform Arm Bracket (part #1076)
  • 2 x Square Spring Clips (part #1146)
  • 1 x Stud Bracket (part #1003), Stud Bracket Narrow (part #1005), Stud Bracket Bent Long (part #1006), or Stud Bracket Bent Short (part #1004)

For platforms:

  • Interlocking Planks (part #ILP3 to ILP6)
  • Plank Staples (part #1158)
  • Plank Clamps – Single (part #1087) / Double (part #1080) / Tube (part #1079)
  • Toeboards (part #1210)
  • Toeboard Clips – Plank (part #1211)

Other:

  • Lock Pins (part #1182)
  • R-Clip (part #1900
  • Ladder (part #LAD3.6/#LAD5.4)

Note: exact components required will vary depending on set-up and site specific requirements

INTAKS® Scaffolding & Edge Protection solutions

Want to learn more then get in touch with us today

Thank you! Your submission has been received!
Oops! Something went wrong while submitting the form.